A+ Rated for 23 years
 












Search Engine Marketing & Optimization

You are here:Home > HORNS & SIGNALS
Sort By:
Page of 1
Horn in mounting box Crane / Hoist Hour Meter Panel Mounted Temperature Thermometer
Our Price: $66.00
Our Price: $70.60
Our Price: $119.50
Pt.#MT4-115-S   Horn with WBB-S surface mounted box. The multi-tone electronic signal is field selectable to provide eight distinct tones. 91-97 dba. standard white color. For indoor applications. 115 Volt operation. Keep track of your equipment usage with an inpanel hour meter. This AC Voltage Hour Meter registers Elapsed Time Up to 99999.9 Hours, Bezel Face 2.50 Inches Round, Length from Back to Bezel 2.75 Inches, Elapsed Time Indicators, Non Resettable, Input Voltage 110 to 120 @ 60 Hz, 3 Watts, Numbers White on Black, Decimals Black on White, Material Black Styrene, Indoor Use Only, Continuous Duty Accuracy 100%, Start/Stop Accuracy to Plus/Minus 50 msec, Flange Mounts In 2.25 Inch Diameter Hole, Includes 22 Gauge Wire Leads 6 Inches Long, Mounting Hardware Keep track of the temperature in your Panels.  Switch Plate Thermometer, Digital, 3 Digit LED Display, Temp. Range (F) -40D to 230D, Switch Plate Mounting, Accuracy +/-1%, Line Length (In.) 60, Line Length (Ft.) 5, Sensor Dimension (In.) 1.18 x.27, Power Source 110 VAC, Case Material ABS, Tube Material Plastic Coated, Lens Material ABS, Meets UL, NSF Certified Yes, Includes Battery Back-up Wire Assembly
Horn - Strobe Combination Crane Lights - Metal Halide for Indoor Service Explosion Proof Vibrating Horn
Our Price: $235.00
Our Price: $265.00
Our Price: $967.00
crane horn with strobe Explosion Proof Vibrating Horn
120 VAC MULTI-TONE HORN AND STROBE COMBO
Compact Horn Strobe combo for applications requiring more flash intensity. This economical setup in combination with a Multi-Tone Horn has the following tones: Horn, Bell, March Time Horn, Code-3 Horn, Code-3 Tone, Slow Whoop, Siren, Hi/Lo - all dip switch field selectable.

The Multi-Tone Horn/Strobe is designed with a 1/2" conduit entry at the bottom of the junction box. The strobe light used for this combination is the Tomar Brand Microstrobe.
Crane Lights
Cast aluminum spring loaded socket and reflector support provides a reliable indoor crane light for 250 DC Mercury Vapor and AC HPS lamps. The highly polished reflector gives a medium beam spread. For additional protection against shock and vibration, include one of the shock mounts illustrated below.

The 250 DC Mercury Vapor fixture & lamp combination utilizes a current limiting resistor for operation of a mercury vapor lamp on 250 DC input voltage. This resistor acts as a special ballast for 250 DC and is intended for overhead crane applications only, not for general illumination.

Pt.# ECP878EX-N5

Explosion Proof Vibrating Horn is constructed of a heavy duty casting that has a heat flowed expoxy finish for corrosion resistance. This explosion proof horn is intended for use in potentially explosive atmospheres. Applications for this product are found in the oil and gas, and petrochemical industries, where high decibel vibrating horn signals are required. Two mounting brackets are provided on either side of the unit for wall mounting. The housing is tapped on one side for 3/4" (19mm) conduit to allow for field wiring installation. For use in dusty, hazardous atmospheres where a distinctive, urgent signal is required for timing, scheduling, paging and general alarm applications. Typical applications include use in mines, petroleum plants, gas plants, grain elevators, flour mills, paper mills, textile plants and tankers.as well as many others. UL Listed for Class I, Division 1 and 2, Groups B, C, and D; Class II, Division 1 and 2, Groups E, F, and G; and Class III locations, UL Listed for outdoor locations, NEMA Type 4X Rated, 97dBA output at 10 feet. 120VAC, or Select the 24 Volt DC version (879EX-G1) above when ordering
Explosion Proof Horn Strobe Combination
Our Price: $3,937.00
Explosion Proof Horn Strobe Combination
Pt.#ECPA-S2UL120 Explosion proof hazardous location strobe status lights, with audible alarm (unit includes 2 colored strobes with cast aluminum guards) has been designed to include both visual and audible signaling in a factory assembled combination with mounting plate. This assembly suits various Class I, Division 2 offshore and onshore applications. Available in 120 Volt AC, includes 2 xenon strobes with an intense 15 joule flash intensity (select colors above when odering). This version is constructed in GRP components and aluminum back plate, the sounder is electronic and allows for field selection of 1 tone from 27 available. The Db volume output is 108dBA +/-3 dB at 1 meter and is tone dependent. UL listed Class 1, Div. 2, Groups A through D. Temperature range 58F to +131F. GRP Components. Pre-Wired with junction box, mounting plate, and 3/4" NPT opening. 120VAC.